Add-on hardware modules and accessories for analog and digital cards.
Digium Telephony boards come standard with full-height brackets for standard mounting. Optional low-profile brackets are available for all low-profile cards to enable mounting into 1-U servers.
FXS modules provide ringing voltage and battery to telephones or handsets and require substantial amount of 12V DC power in order to operate properly. The PCI interface on motherboards cannot provide sufficient quantities of this voltage necessary to ring 4, 8 or 24 modules. As a solution, Digium analog cards are mounted with a 4-pin disk-drive or Molex connector on the base board. This connector must be supplied with an internal power connector from the system’s power supply if FXS modules are in use.
DSP-based echo cancellation modules for all of our analog and digital (T1/E1/J1) cards with the VPMOCT series modules.
Straight-through and cross-over cables for connecting Digium T1/E1 interface cards and T1/E1 ports, telephone cables for interfacing analog cards, and timing cables for digital cards.
Use this kit of twelve RJ11/4 plugs and a crimping tool to hardwire your Sangoma A200 system.
6 position, 2 conductor, 24-port/1 RMS (rack mount space) Telco patch panel. Integrated with 1 Telco connector and includes # 12 rack screws. Uses a female amphenol connector.
Sangoma’s T1/E1 line tapping solution is a high performance, robust and inexpensive toolkit that gives you complete access to the T1/E1 voice and signalling interfaces. Based on the popular A102, A104 and A108 AFT cards, the system supports the line tapping of one, two and four T1/E1 lines per card respectively.
The Digium 2400P Rack Mount Breakout Box is a 19 inch 1U, rack mountable patch panel featuring a 50-pin male connector and its 24 female RJ-11 connectors are wired with two conductors for single line operation.
Product Code: 1ACC24PPP
Up to four TE2/4XXP cards to share the same sync (timing) source from the T1/E1 provider, or provide a consistent sync source across multiple cards.
Product Code: 3112-00001
The 6 foot 50-pin telephone cable interfaces the TDM2400P card with regular RJ-11 two-conductor telephone cables and is used in combination with either the 24-port, 2-wire breakout box (ACC2400PBO), or the 24-port, 2-wire 19″ rack mount unit (ACC2400PPP)
Product Code: 3113-00002
The timing cable allows up to three Hx8 or TE8xx cards to share the same sync (timing) source from the T1/E1 provider, or provide a consistent sync source across multiple cards.
Product Code: 3112-00003
The 7 foot shielded, cross-over cable is used for connecting Digium T1/E1 interface cards to the PSTN or other T1/E1 equipments. The cross-over cable is the standard cable that should be used to connect T1/E1 ports to T1/E1 ports or equipment.
Product Code: 3113-00016
For the A142, A144 Standard | ROHS: Yes | Length: 6′
For the A142, A144 Standard | Male | ROHS: Yes | Length: 6′
For Sangoma cards Only Sold Separately | Length: 6′
Back-to-back, cross over cable (x/o) Special Order | ROHS: Yes | Length: 20’
RJ45 E1/T1 Cable Standard | ROHS: Yes | Length: 6′
A200 Analog Cable Standard | ROHS: Yes | Length: 6′
For a A400 Analog Cards Standard | ROHS: Yes | Length: 6′
A200 Analog Cable Standard | ROHS: Yes | Length: 6′
Fax Synch Cable Only Sold Separately | ROHS: Yes | Length: 8′
Dual Synch Cable Only Sold Separately | ROHS: Yes | Length: 8”
For a A400 Analog Cards Standard | ROHS: Yes | Length: 6′
Power Adapter for FXS Only Sold Separately | ROHS: Yes | Length: 8″
Standard cable for A142R
Standard cable for A142V Standard | ROHS: Yes | Length: 1′
Standard cable for A144R Standard | ROHS: Yes | Length: 1′
Standard cable for A144V Standard | ROHS: Yes | Length: 15′
Only Sold Separately | ROHS: Yes | Length: 6″
Standard cable for A142V Standard | ROHS: Yes | Length: 1′
Special Order Only Sold Separately | Length: 10′
Special Order | ROHS: Optional | Length: 10′
